OKBICHI for iPhone Be super welcome 8 Screen Replacement LCD Inch Black Di 4.7 Replacement,$14,/Hildebrandist1920208.html,LCD,Di,globalbirdrescue.org,Cell Phones Accessories , Accessories,Inch),,iPhone,Black,OKBICHI,Screen,(4.7,for,8 OKBICHI for iPhone Be super welcome 8 Screen Replacement LCD Inch Black Di 4.7 Replacement,$14,/Hildebrandist1920208.html,LCD,Di,globalbirdrescue.org,Cell Phones Accessories , Accessories,Inch),,iPhone,Black,OKBICHI,Screen,(4.7,for,8 $14 OKBICHI for iPhone 8 Screen Replacement Black (4.7 Inch), LCD Di Cell Phones Accessories Accessories $14 OKBICHI for iPhone 8 Screen Replacement Black (4.7 Inch), LCD Di Cell Phones Accessories Accessories

OKBICHI for iPhone Be super 2021 model welcome 8 Screen Replacement LCD Inch Black Di 4.7

OKBICHI for iPhone 8 Screen Replacement Black (4.7 Inch), LCD Di

$14

OKBICHI for iPhone 8 Screen Replacement Black (4.7 Inch), LCD Di


Product Description

iPhone 8 screen replacement iPhone 8 screen replacement iPhone 8 screen replacement iPhone 8 screen replacement
OKBICHI iPhone 6 Screen Replacement OKBICHI iPhone 6s Screen Replacement OKBICHI iPhone 7 Screen Replacement OKBICHI iPhone 8 Screen Replacement
Model Number A1549, A1586, A1589 A1633,A1688, A1700 A1660, A1778, A1779 A1863,A1905,A1906
Home Button X X X X
Front Camera X X X X
Ear Speaker X X X X
Proximity Sensor X X X X
Middle Frame
Replacement Kit
Screen Protector
iPhone 8 screen replacement

Test before installation

1. Please check if the screen is intact.

2. Power off your iPhone and remove the two screws with screwdriver.

3. Use the spudger to separate screen from rear case along four edges.

4. Open the screen from rear case carefully to avoid the damage on cables.

1

2

3

4

FAQ:

Why the phone works but screen is showing nothing after installed?

-When reassembling your phone, the display data cable may pop off its connector.

This can result in white lines or a blank screen when powering your phone back on.

If that happens, simply reconnect the cable and power cycle your phone.

The best way to power cycle your phone is to disconnect and reconnect the battery connector.

Why the screen has been installed and worked fine for a few days/weeks, but the touch function of it is not working correctly now?

-This is because the digitizer cable might lose connection if not plugged in firmly, you can transfer the foam that attaches to the back of original digitizer cable connector onto the new one, which can make sure the connector stays connecting to the motherboard.

Why the screen is fine when testing it but the touch is not working well after the screen is assembler?

-In this case, please check whether the battery is swollen or not.

If yes, it is really likely that the digitizer cable connector will be loosen after the screen is assembled.

In additon, a swollen battery has a high possibility to cause overheat or explosion.

Therefore, we would hiahly recommend you to replace your battender this circumstance.

Why the Touch ID can not work?

-(1) Because only the original home button has Touch ID and fingerprint identification function.

So please transfer it from your original screen to the new one

(2) Remove the metal cover of Home Button again, and then check whether the cable connector is connected properly or damaged.

Why my Ear Piece Speaker/Front Camera did not work?

-(1) These components have a connector connecting to the logic board.

Please make sure they were fully connected.

(2) You will also need to re-power the phone to active the function.

OKBICHI for iPhone 8 Screen Replacement Black (4.7 Inch), LCD Di

Submit Cheat
Hola!
You can post cheats here and contribute to our community.